Arduino Basic and Installation | What is Arduino | Introduction of Ardui...

Arduino Basic and Installation


In this Video you see about Introduction of Arduino and Most commonly used types of Arduino. 







Range values for Potentiometer and Joystick  while using arduino



How to download and Install Arduino.

Comments

Post a Comment

Popular posts from this blog

Servo motor controlled by Joystick using Arduino & Transceiver - Wireles...

Image
Circuit Diagram: Required Components: Arduino uno/nano - 2 Nos Battery - 2 Nos Transceiver - 2 Nos Servo Motor - 2 Nos Joystick - 1 Nos Program Code: Transmitter Code: #include <SPI.h> #include "RF24.h" #include "nRF24L01.h" int potpin1 = A1; int potpin2 = A2; int data[2]; RF24 radio(9,10); const uint64_t pipe=0xE8E8F0F0E1LL; void setup() { Serial.begin(9600); radio.begin(); radio.openWritingPipe(pipe); } void loop(){ data[0] = analogRead(potpin1); data[1] = analogRead(potpin2); data[0] = map(data[0],0,1023,5,175); data[1] = map(data[1],0,1023,5,175); radio.write(data,sizeof(data));    {     Serial.println(data[0]);     Serial.println(data[1]);     } } Receiver Code: #include <SPI.h> #include "RF24.h" #include "nRF24L01.h" #include <Servo.h> Servo servo1; Servo servo2; RF24 radio(9,10); const uint64_t pipe=0xE8E8F0F0E1LL; int data[2]; void setup() {   servo1.attach(5);   servo2.attach(6);   Serial.begin(9
Read more

DC motor controlled by Joystick using Arduino & L298N Motor driver - Wireless Connection

Image
Circuit Diagram: Required Components: Arduino uno/nano - 1 Nos Battery - 1 Nos DC Motor - 2 Nos L298N Motor Driver - 1 Nos Joystick - 1 Nos Transceiver - 2 Nos Program Code: Transmitter Code: #include <SPI.h> #include "RF24.h" int x_axis = A1; int y_axis = A2; int xvalue; int yvalue; int data[2]; RF24 radio(9,10); const uint64_t pipe=0xE8E8F0F0E1LL; void setup() { Serial.begin(9600); radio.begin(); radio.openWritingPipe(pipe); } void loop() {{ xvalue=analogRead(x_axis); xvalue=map(xvalue,0,1023,0,127); data[0]=xvalue; radio.write(data,1); } { yvalue=analogRead(y_axis); yvalue=map(yvalue,0,1023,128,255); data[0]=yvalue; radio.write(data,1); } Serial.println(xvalue); Serial.println(yvalue); } Receiver Code: #include <SPI.h> #include "RF24.h" const int motorforward = A1; const int motorbackward = A2; const int motorleft = A3; const int motorright = A4; int data[2]; RF24 radio(9,10); // CE,CS
Read more

DC motor controlled by Gyro MPU 6050 using Arduino & L298N Motor driver - Wired Connection

Image
Circuit Diagram: Required Components: Arduino uno/nano - 1 Nos Battery - 1 Nos DC Motor - 2 Nos L298N Motor Driver - 1 Nos Gyro MPU6050 - 1 Nos Program Code: #include <Wire.h> #include <MPU6050.h> #define motor1_pin1 5 //PWM - Digital Pins #define motor1_pin2 6 //PWM - Digital Pins #define motor2_pin1 9 //PWM - Digital Pins #define motor2_pin2 10 //PWM - Digital Pins MPU6050 gy_521; int16_t ax, ay, az; int16_t gx, gy, gz; int motor1_speed1; int motor2_speed1; int motor1_speed2; int motor2_speed2; void setup ( ){ Wire.begin( ); Serial.begin (9600); Serial.println ("Initializing MPU and testing connections"); gy_521.initialize ( ); Serial.println(gy_521.testConnection( ) ? "Successfully Connected" : "Connection failed"); delay(1000); Serial.println("Reading Values"); delay(1000); } void loop ( ){ gy_521.getMotion6(&ax, &ay, &az, &gx, &gy, &gz); ax = map(ax, -17000, 1
Read more